Apr 29, 2012 · I replace this electric motor and it has 4 lugs - I have 3 wires blk, red and white. There is a sticker on motor indicating wiring, but seems only an electrician knows how to interpret. There is CW shaft end (clockwise) =1 = Blue & line speed high; 2 = line common; 3 = line-low speed; 4 = white

May 20, 2014 · The motor is designed to run off of 115 VAC (Low) or 230 VAC (High) voltage. The name plate tells you that at 115 volts the current draw is about 9.0 amps and at 230 volts the current draw is about 4.5 amps. The motor is a single phase motor.

Oct 16, 2016 · I am wanting to hook up a 1/2 hp motor but when i opened it up nothing is labeled that i can see, the sticker on the motor is torn up, unreadable, and i cant tell how it is currently wired, all i can really see is a board with blade connectors on it. I …

May 19, 2004 · I have a single phase, 1HP, 60/50Hz motor than I need to wire a pigtail on. The motor can be wired for 115 or 208-230. I am probably going to use it wired for low voltage. I'm not sure how to connect to my three wire (hot/neutral/ground) pigtail. The wiring diagram for low voltage is: P1 - UNGR D LINE P2, T8, T3 - Tape T2, T5, T4 - Line

Feb 6, 2010 · Replaced an AOSmith 1/2 HP motor w/ 6 wires with a Dayton 1HP (Model# 1TMY5 - Farm Duty Motor, 1 HP, 1725, 115/230v, 56H www.daytonmotors.com) - problem is that the new motor has 8 wires (P1, P2, T1, White, Yellow, Black, Orange and Red) and I can't seem to figure out the correct wiring schematic to connect into the contractor with the four ...

Jul 15, 2012 · black is hot, white is neutral, green is ground. the switch should be on the hot side. the green wire from the cord should be twice as long as the white or black (whichever is longer) coming out of the cord. keep the motor wired for low voltage (120), use 16 or 14ga stranded (not solid) wire and keep the same color scheme (lack for hot, white for neutral).

May 16, 2018 · I recently purchased an IME lathe complete with a 1950's/60's General Electric motor and capacitor. The board the motor and lathe were situated on was a tad tatty, so I decided to make a new one. During the course of which I had to disconnect the wiring and made a diagram of where the three wires were attached.

Jun 5, 2022 · Can anyone help me with the wiring. It is out of a garage door opener and the diagram confuses me. It is a all-o-matic ARD model. I want to bring it back to life, drive with a pic/avr, sensors and triacs/SSRs. Just need some help on the motor wiring to run forward and run it reversed. Newer (very old) diagram attached, but same motor at this one.

Nov 26, 2023 · I'm hoping someone can instruct me on how to connect the wiring to bench test a Leeson 120v reversible electric motor. I've included a picture of the wiring diagram from the side of the motor showing how the five colored wires are currently connected. Here's the sum of my knowledge: ground is blue, so I should connect the green wire from the ...

Oct 3, 2010 · The motor is a variable speed DC motor. Now I may have this backwards but with motors like this (1 HP) I think they use a fixed voltage on the commutator and vary the voltage to the field windings. That may be backwards as I said. I can tell you that using a motor like this for your intended use won't be very easy or practical.